Precision grinding sets the four geometric properties that govern how a roller interacts with a moving web: total indicated runout (TIR), roundness and cylindricity, surface roughness (Ra), and crown. On film-line rolls, grinding typically takes TIR from 0.05–0.10 mm as-turned to 0.005–0.020 mm, reduces Ra from 0.8–1.6 µm to 0.05–0.20 µm — and to 0.005–0.01 µm where chrome is finish-ground and superfinished — and holds crown to ±0.01 mm across faces up to 8 m. Each number maps to a defect class: banding, tension pulsing, air entrainment, cross-web gauge. Grinding is therefore not a finishing step appended to manufacture; it is where the roller's process behaviour is decided.
· Runout converts into a once-per-revolution defect whose wavelength equals the roll circumference, which makes it diagnosable from the film itself
· Cylindricity and roundness control tension stability along the face, and lobing is often mistaken for a control-loop problem
· Roughness governs air entrainment, contact area, gloss and plate-out — not merely appearance
· Crown is a ground profile that compensates deflection, and it must be matched across a nip pair
· Finish grinding on the chrome generates the final tolerance; plating cannot correct an out-of-round shell
· Balancing must follow the last grinding pass, never precede it
· Acceptance requires measurement in the bearing housing, not between centres
|
Item |
Description |
|
Function |
Generate final geometry, profile and surface texture on a film-line roller |
|
Scope |
Turning, pre-grinding, chrome plating, finish grinding, superfinishing, balancing, inspection |
|
Critical tolerances |
TIR, cylindricity, Ra, crown, balance grade, chrome thickness |
|
Typical TIR |
0.005–0.020 mm by duty |
|
Typical Ra |
0.005–0.4 µm by duty |
|
Typical crown |
0.02–0.10 mm on diameter |
|
Shell materials |
Forged alloy steel, stainless steel; hard chrome 0.05–0.15 mm at 800–1000 HV |
|
Service life |
10–15 years with two to three regrinds |
|
Regrind cost |
25–40% of a new roll; 0.05–0.15 mm off diameter per cycle |
Precision grinding is abrasive machining of a roller's working surface and journals to a specified diameter, roundness, cylindricity, surface roughness and axial profile. For film production it is the last operation capable of correcting geometry, because both plating and polishing reproduce the shape presented to them.
Large steel roll end being turned with coolant on an industrial lathe
ALT: Large steel roll end being turned with coolant on an industrial lathe before precision grinding
Grinding removes material as thousands of shallow, overlapping cuts made by abrasive grits bonded into a wheel. The resulting surface is a function of wheel specification and condition, infeed per pass, traverse rate, spark-out time and coolant delivery — not of operator judgement. Two results are produced simultaneously: the diameter and profile converge on the drawing, and the surface texture is generated at micrometre scale.
The process is also diagnostic. Because the wheel follows the machine guideways and the workpiece centres, grinding reveals errors that turning conceals: taper from tailstock misalignment, lobing from inadequate work support, a step from interrupted infeed, chatter from wheel imbalance or worn guideways. A well-run grinding operation corrects them; a poorly run one reproduces them with a finer surface finish.
Three process variables matter most in practice:
· Wheel specification and dressing. A wheel that is glazed cuts by rubbing, generating heat and a torn surface; one that is too soft loses form and produces taper. Continuous or frequent dressing keeps both geometry and finish stable over a 6–8 m traverse.
· Infeed and spark-out. The final passes should remove microns, with a dwell at the end of the face so the wheel cuts out deflection rather than leaving a step.
· Coolant. Flood cooling at the contact zone prevents thermal damage and washes swarf away; starving the cut produces a polished-looking surface with subsurface damage that appears later as plate-out or chrome adhesion failure.
Previous: resin feeding → extruder → die head → casting roll and pinning unit
Current: the ground roll in its working position — CASTING ROLL, BOPP CHILL ROLL, MDO PREHEATING ROLL or MDO STRETCHING ROLL, CORONA ROLL, coating or metering roll, guide and idler
Next: MDO → TDO → winding → slitting → FILM CONVERTING ROLLS
Grinding belongs to the roller's manufacturing chain rather than the film's process chain, yet its output is felt at every stage above. A casting roll finished to Ra 0.01 µm and a corona treater roll held to 0.02 mm runout are the same discipline applied to different duties. The CASTING FILM ROLLS and BI-ORIENTED FILM ROLLS pages show how the same clauses are written for different line positions.
|
Roll duty |
TIR |
Cylindricity |
Ra |
Balance |
|
Casting / chill roll |
0.005–0.015 mm |
≤ 0.01 mm |
≤ 0.01 µm |
G1.0 |
|
MDO preheat / stretch |
0.010–0.020 mm |
≤ 0.01 mm |
0.05–0.2 µm |
G2.5 |
|
Corona treater |
≤ 0.020 mm |
≤ 0.01 mm |
0.2–0.4 µm |
G2.5 |
|
Coating / metering |
0.005–0.010 mm |
≤ 0.008 mm |
0.1–0.2 µm |
G2.5 |
|
Guide / idler |
≤ 0.025 mm |
≤ 0.02 mm |
0.4 µm |
G6.3 |
|
Embossing / calender |
0.005–0.015 mm |
≤ 0.01 mm |
0.05–0.2 µm |
G2.5 |
|
General industrial |
≤ 0.10 mm |
— |
1.6 µm |
G6.3 |
The final row is not a straw man. Catalogue "standard" rolls are built to it, and specifying a film-line roll at that level is the most frequent single cause of a machine that will not hold gauge. The difference between 0.10 mm and 0.010 mm is not a refinement; it is a different product. Thermal duties add a second specification layer, covered on the PRS COOLING ROLL page.
1. Rough turn and stress relief. Welding and heavy material removal leave residual stress. A shell that is not stress-relieved before finishing will move after grinding, usually within weeks, and the movement appears as runout that nobody can explain.
2. Semi-finish turn. Leave 0.3–0.5 mm on diameter for grinding — and, critically, leave enough stock to allow two or three future regrinds. A roll turned to nominal with 0.05 mm of stock has a service life of one campaign.
3. Pre-grind the substrate. Geometry is established here. Plating cannot correct an out-of-round or tapered shell; it copies it with a harder surface.
4. Hard-chrome plating. Typically 0.05–0.15 mm at 800–1000 HV, sometimes 0.20 mm for aggressive duties. Thickness and hardness should be mapped at both ends and the centre, because variation changes both wear life and heat path.
5. Finish grind on the chrome. This is where final TIR, cylindricity and Ra are generated. It is also the step most often omitted in low-cost offers, where the chrome is polished rather than ground.
6. Superfinish or polish. A controlled final texture, with the lay direction specified. Polishing improves Ra but follows the shape it is given, so it cannot correct geometry.
7. Dynamic balancing. Removing material from a large shell changes mass distribution. Balance to G2.5 for general duties and G1.0 or better for optical and capacitor work — after the last grind, never before.
8. Inspection in the bearing housing. Runout measured between centres excludes bearing-seat error and housing alignment. A roll can read 0.018 mm on a lathe and 0.062 mm in its housing, and only the second number predicts behaviour at line speed.
A roll with runout e modulates contact pressure, web tension or nip gap once per revolution. The resulting defect repeats at the roll circumference, so the spacing of bands in a gauge or coating trace identifies the diameter directly:
|
Measured band spacing |
Implied roll diameter |
Frequency at 400 m/min |
|
0.94 m |
Ø300 mm |
about 7.1 Hz |
|
1.26 m |
Ø400 mm |
Pessoa de Contato: Mr. Maple
Telefone: +86 17778255675
Fax: 86--311-80690567